High‑Reliability Flat Key Connection Structure Design and Precision Assembly Process for Hot Die Forging Press Brake


Aiming at the engineering problems of the conventional flat key connection between the brake housing and frame of a hot die forging press, such as difficult precise control of fitting accuracy, high risk of loose “key rolling” failure, poor on-site maintainability and short service life of connecting components, this paper proposes a novel flat key positioning connection structure and its precision assembly method based on the concept of “controllable interference fit + mechanical locking”. The core of the structure lies in an integrated convex flat key design. The flat key connection achieves precise interference fit (interference: 0.02–0.03 mm) with the keyway of the brake housing through liquid nitrogen cryogenic cooling and rewarming process, while the fixed connection to the frame forms a detachable rigid joint with the frame via high-strength bolt groups and locating pins. This paper elaborates on the innovative design principle of the structure and the parametric design of key components, including the precision assembly process for tolerance fits and assembly torque. Industrial application results show that, compared with the traditional structure, the new connection structure reduces the wear rate of keyways by more than 70%, effectively avoids abnormal wear of associated components caused by connection failure. It is expected that the service life of the main frame structure can be extended to more than 10 years, the overall overhaul cycle of the equipment is prolonged by approximately 50%, and the time and cost of a single maintenance are reduced by over 60%. This research provides a reliable technical route as well as theoretical and practical basis for the design of critical transmission connection structures under heavy-load and high-frequency impact conditions.

As core equipment in modern heavy manufacturing, hot die forging presses are widely used for the production of critical forgings in the automotive, aerospace and military industries. Its operation involves huge impact loads and periodic torque; therefore, the dynamic reliability of the whole transmission chain is of great importance. As the key braking unit of the press crankshaft system, the connection between the brake housing and the frame must transmit braking torque stably and efficiently and withstand long-term alternating stress.

At present, the conventional flat key connection widely adopted in the industry usually adopts a pair of symmetric keyways and grooves on the brake housing and frame, into which rectangular flat keys are embedded, supplemented by circumferential bolts for fastening. Several inherent drawbacks have been exposed during practical operation.

(1) Difficulty in fitting accuracy control. If the fit between the flat key and keyway is too loose, fretting wear and axial displacement tend to occur under the combined effect of bolt clearance and impact load, resulting in “key rolling”, transmission failure and even equipment damage and safety accidents, with extremely high single repair cost (exceeding 300,000 RMB). If the fit is too tight, assembly and disassembly become extremely difficult and often require hammering, which easily damages mating surfaces and impairs assembly accuracy and efficiency.

(2) Poor maintainability. Once the flat key or keyway of the traditional structure is worn, maintenance usually requires large-area repair or even replacement of the frame or housing, featuring long maintenance cycles (up to 72 hours), high costs and irreversible damage to the equipment body.

(3) Insufficient long-term stability. Under prolonged vibration and impact, the flat key connection suffers from fatigue wear, the fitting clearance gradually increases, the torque transmission capacity declines, and a vicious cycle forms, which undermines the stable long-term operation of the equipment.

To tackle the above problems, scholars at home and abroad have carried out a series of studies, such as adopting double-key structures and improving materials. However, most of these approaches fail to fundamentally resolve the contradiction between fitting accuracy and maintainability. Drawing on the rich experience of FAW Forging (Jilin) Co., Ltd. in the operation and maintenance of large presses, this paper carries out systematic innovation from the perspectives of structural principle and assembly technology, and proposes a new flat key positioning connection structure and assembly method to unify connection reliability, assembly manufacturability and maintenance economy.

Design of the New Flat Key Positioning Connection Structure

Overall Structural Scheme

As shown in Figure 1, the flat key positioning connection structure designed in this paper mainly consists of three parts: the frame, the brake housing and the specially fabricated flat key. Its core design idea transforms the conventional “single embedded body” mode into a composite connection mode of “interference fit at the end + mechanical locking at the root”.

Schematic Diagram of the Overall Structure of Frame and Brake Housing

Figure 1 Schematic Diagram of the Overall Structure of Frame and Brake Housing

Innovative Design of Key Components

(1) Flat key structural design.

The flat key design represents the core innovation of this structure. As shown in Figure 2, it adopts an integrally forged convex shape and can be clearly divided into two functional zones:

 

Schematic Diagram of Convex Flat Key Structure

 

Figure 2 Schematic Diagram of Convex Flat Key Structure

 Schematic Partial Section View of Frame and Brake Housing

Figure 3 Schematic Partial Section View of Frame and Brake Housing

① Flat key connection section: This protruding part of the convex profile is designed for precise interference fit with the keyway of the brake housing. Its width is calculated precisely to ensure sufficient contact stress on the side walls of the keyway after rewarming for torque transmission.

② Frame fixing connection section: This is the base part of the convex profile, exposed on the side wall of the brake housing. High-precision locating pin holes and frame threaded holes are arranged on its top surface. This design changes the connection mode between the flat key and the frame from the conventional “embedded groove” to “surface bonding and fastening”, which thoroughly avoids stress concentration and structural weakening caused by machining deep grooves on the frame.

(2) Keyway and fit design. At least three keyways are evenly distributed circumferentially on the lower end face of the outer edge of the brake housing. Compared with the traditional double-key arrangement, this multi-keyway design enables more uniform load distribution, reduces the stress on each individual key and improves transmission stability. The keyway is designed as a unique double-sided open slot to facilitate cryogenic assembly of the flat key. The lower end face of the flat key can be coplanar with the lower end face of the housing, ensuring flat contact with the mounting surface of the frame.

(3) Material selection. The flat key is made of 40Cr medium-carbon alloy steel. Its chemical composition (C: 0.37%–0.44%, Cr: 0.80%–1.10%) endows it with excellent comprehensive mechanical properties. After quenching and tempering, its strength, toughness and fatigue resistance are superior to those of commonly used 45 steel, making it particularly suitable for heavy-load and impact conditions.

Working Principle and Mechanical Advantage Analysis

The connection reliability of this structure is guaranteed by a dual mechanism. (1) First guarantee (interference fit): The interference fit between the flat key connection section and the keyway eliminates fitting gaps at the micro level and forms tight surface contact. It can not only transmit torque effectively, but also significantly suppress fretting wear induced by vibration and impact, fundamentally slowing the loosening of the fit.

(2) Second guarantee (mechanical locking): The frame fixing connection section is firmly locked onto the frame by locating pins and high-strength bolts. The locating pins provide strong shear resistance and bear the main circumferential torque; the bolt group generates large preload to produce friction and compress the flat key, effectively restraining its displacement tendency in any direction.

Benefiting from this dual-protection mechanism, the structure maintains extremely high connection stiffness and stability even under extreme working conditions.

Precision Assembly Method and Process Control

A rational assembly method is essential to realize the design intention. The core of this method is to achieve damage-free interference fit assembly through precise tolerance design and controllable physical processes.

Assembly Procedure

The detailed steps are as follows: (1) Pre-positioning of the housing: Fasten the brake housing preliminarily to the preset position on the frame using high-strength housing fastening bolts (e.g., Grade 10.9, M36). This step provides a reference for subsequent flat key installation.

(2) Cryogenic assembly of the flat key: This is the critical process. The qualified machined flat key is immersed in liquid nitrogen at −196 ℃ for deep cryogenic treatment for 18–25 minutes to achieve uniform shrinkage. It is then quickly inserted into the corresponding keyway. At this moment, the shrunk flat key connection section forms a clearance fit with the keyway and can be seated easily without violent assembly such as hammering. After standing and rewarming at room temperature, the flat key returns to its original size and forms the designed interference (0.02–0.03 mm) with the keyway.

(3) Final fastening of the housing: Tighten the housing fastening bolts with a calibrated torque wrench at 2250 N·m to ensure tight bonding between the housing and the frame mounting surface.

(4) Machining of matched holes on the frame: Guided by the locating pin holes and threaded holes on the flat key, drill and ream the corresponding locating holes and threaded bottom holes on the frame. This matching machining process ensures high coaxiality and positional tolerance between the holes on the frame and those on the flat key.

(5) Completion of mechanical locking: Drive locating pins (e.g., φ20 mm) into the locating pin holes and the frame locating holes by interference fit. Then pass high-strength bolts (e.g., Grade 10.9, M30) through the threaded holes on the flat key and tighten them onto the frame at 1600 N·m to complete the whole rigid connection.

Key Process Parameters and Control

Tolerance fit: The keyway width is machined to H7 tolerance, and the width of the flat key connection section is machined to r6 tolerance. This fit relation is the foundation for achieving accurate interference.

Assembly torque: The tightening torques in Step S3 and S5 are the guarantee of sufficient preload, which must be strictly controlled within the specified range by torque wrenches (housing bolts: 2000–2500 N·m; flat key bolts: 1400–1800 N·m).

Industrial Application and Performance Analysis

To verify the practical performance of the structure, it was applied to the brake of a 2000-ton hot die forging press. The equipment originally adopted a traditional double-flat-key structure, and keyway repair was required on average every 18 months. Since the adoption of the new structure, the press has operated continuously for 24 months.

Performance Comparison

Key performance indicators of the new and traditional structures obtained through periodic shutdown inspection and measurement are shown in Table 1.

Table 1 Performance Comparison between the New and Traditional Structures

Performance Comparison between the New and Traditional Structures

 

Comprehensive Benefit Analysis

To comprehensively and quantitatively evaluate the practical value of the new flat key positioning connection structure, an in-depth benefit analysis is carried out from three dimensions: reliability, economy and maintainability, combined with specific data and cases.

(1) Reliability benefit: eliminating faults fundamentally and improving the overall equipment efficiency (OEE). ① Elimination of critical faults: the fatal “key rolling” failure of the traditional structure has a zero occurrence rate after the application of the new structure. This not only avoids the direct repair cost of more than 300,000 RMB for a single repair, but also prevents the loss of whole-line production interruption caused by unexpected shutdown. ② Significant reduction in wear rate: after tracking measurement over two overhaul cycles, the precision of keyway side walls is inspected by a coordinate measuring machine. The data show that the average wear depth of the main bearing surface of the keyway decreases from 0.15 mm/year for the traditional structure to less than 0.045 mm/year for the new structure, representing a 70% reduction in wear rate (Table 1). It verifies that the dual mechanism of controllable interference fit and mechanical locking effectively suppresses fretting wear and fundamentally prolongs the service life of core components. ③ Avoidance of associated damage: loosening of the flat key in the traditional structure causes abnormal radial runout and impact between the brake housing and crankshaft, which further triggers cascading damage to associated components such as bearings and seals. Benefiting from the rigid connection, the new structure ensures stable operation of the transmission chain, and the repair rate of abnormal wear of associated components is reduced by 85%, bringing additional savings in maintenance costs.

(2) Economic benefit: great optimization of life cycle cost (LCC). The economic benefits of the new structure are reflected in direct cost savings and indirect efficiency improvement. ① Direct maintenance cost. Single repair cost: the comprehensive cost of a single repair for the traditional structure (including keyway surfacing, machining, new key fabrication, etc.) is approximately 300,000 RMB. When wear occurs on the new structure, only standardized flat key components need to be replaced at a cost below 50,000 RMB, saving more than 250,000 RMB per repair. Periodic cost: the traditional structure requires a major overhaul every 3 years on average, while the overhaul cycle of the new structure can be extended to 6 years. For a 20-year service life of the equipment, the traditional structure needs about 6–7 major overhauls with a total cost of 1.8–2.1 million RMB; the new structure only requires about 3 replacements of core components at a total cost of around 150,000 RMB. Over the whole life cycle, more than 1.5 million RMB can be saved merely in maintenance expenses.

② Indirect operating cost. Shutdown cost: the new structure cuts the single maintenance time from 72 hours to 8 hours, saving 64 hours. Spare parts inventory cost: the traditional scheme requires stocking large key blanks and repair materials of various specifications, occupying capital and storage space. The new structure realizes standardization and modularization of flat keys, reducing the variety and value of spare parts inventory by approximately 60%.

(3) Maintainability benefit: the maintenance mode is upgraded from “destructive overhaul” to “preventive replacement”. ① Transformation of operation mode: traditional maintenance is destructive work involving cutting and welding on the frame body, with complicated procedures and poor controllability of quality. Maintenance of the new structure adopts modular replacement with standardized workflows, lowering dependence on operator skills and achieving highly controllable maintenance quality. ② Safety and labor intensity: high-risk operations such as high-temperature welding and heavy hammering at height are eliminated, and on-site safety risks are greatly reduced. No heavy hammer striking is required during assembly, so labor intensity is markedly decreased. ③ Optimization of maintenance strategy: as the flat key becomes a sacrificial part with predictable service life, the maintenance strategy can be transformed from conventional breakdown maintenance or periodic overhaul to condition-based predictive maintenance. By arranging stress monitoring points on the flat key or conducting regular measurement, replacement can be scheduled before performance degradation to realize planned shutdowns, making equipment maintenance management more proactive and scientific.

Conclusion and Prospect

Aiming at the key technical problems of the brake for hot die forging presses, this paper successfully designs and verifies a new flat key positioning connection structure and its assembly method. The conclusions are as follows: (1) The proposed composite connection structure adopting the convex flat key with “controllable interference fit + mechanical locking” has clear theory and reasonable design. It effectively solves the contradiction between reliability and maintainability of traditional flat key connections under heavy-load impact conditions. (2) The precision assembly process centered on liquid nitrogen cryogenic assembly and matched drilling ensures assembly accuracy and damage-free installation, providing process support for the performance of the structure. (3) Industrial application fully proves the superiority of the structure. It greatly improves connection reliability and equipment service life while substantially cutting maintenance cost and time, and possesses high engineering popularization value.

Future research can be carried out in the following directions: further fine optimization of the interference between the flat key connection section and the keyway, establishment of a life prediction model based on finite element analysis, and extension of this innovative connection concept to similar transmission connection positions of other heavy-duty equipment.